CarPro Gliss 50ML

Specifications:

• Durability: 12 Months +/-.
• Coverage: 20ml per coat +/-.
• Water contact angle: 110°.
• Recommended working temperatures: 50F to 90F.

Directions:

• Wash with CARPRO Reset, decontaminate, and polish with CARPRO Reflect. If a heavier cut is needed, may start with CARPRO ClearCut.
• Wipe down with CARPRO Eraser (vehicle must be 100% dry and free of moisture or dew).
• Drag two lines of product across the length of suede wrapped applicator.
• Apply evenly across the surface, approximately 2 ft x 2 ft section at a time. Any overlap from one section to the next must be within a couple of minutes for even application.
• Add more product to the applicator as needed to keep a wet, even application.
• Gliss will flash fast and when a white haze forms, immediately wipe off all residues using a microfiber towel.
• If haze is left on too long then reapply and immediately wipe off. If layering on top of itself, wait 1 hour between coats. If IR is cured, you may repeat it immediately. Total cure time: 6 hours.

Recommended Surfaces:

• Paint.
• Metal.
• Plastic.
• And many other non-porous surfaces. 

Precautions:

• Keep the container tightly closed after use.
• Store in a cool dry place.
• Keep away from children.
• Do not ingest.

FAQ'S

Q. What does Gliss mean?
A. Gliss in French means very slick surface.

Q. Does Gliss perform as a sealant or a coating?
A. It is a lighter version of the CQUARTZ coatings.

Q. Can it be used on top of Reload, Essence Extreme, or Essence Plus?
A. No since they will not allow the coating to bond to the surface.

Q. Can you use it as a stand-alone coat?
A. Yes it’s very easy to use and will bond well on bare paint.

Q. Do you need to use Eraser pre-coat?
A. Yes to ensure the surface is free of any oils that will prevent the coating from bonding. If a wax or sealant has been previously applied to the surface they will need to be stripped as Eraser will not remove them.

Q. Can we use CQUARTZ on top of Gliss?
A. No.

Q. Can Gliss be applied over a previously coated car which was done a few months ago?
A. Yes.

Q. Is there a time that you should not apply Gliss on top of a CQUARTZ coating?
A. There is a time at which Gliss is not going to bond as well to a weathered coating. The exact point at which that happens is impossible to say due to all the variables involved and the impossibility of testing each one. What I CAN say is that we tested it on top of a 2-month-old coating with good results and it seems to have bonded well. The prep we would recommend for an aged coating if you are not polishing is as follows:

• Wash with CARPRO Reset.
• Rinse.
• Decontaminate with CARPRO Iron X.
• Rinse.
• Use CARPRO Spotless (if needed). 
• Give one final wash again with CARPRO Reset. 
• Rinse and dry.
• Wipe down with CARPRO Eraser.
• Coat.

Q. Does it crystallize like the CQUARTZ coatings?
A. No, it is not meant to add hardness. The main purpose was to add protection from water spots as high content Sio2 based coatings’ weak point is water spots.

Q. Can we top the Gliss with Reload?
A.  Yes but it is not necessary. However, if you choose to do so Reload can be applied after 12 hrs.

Q. Does Gliss attract dust over the surface?
A. Gliss uses inorganic oils to produce slickness, together with its anti-static properties it will attract much less dust than most ceramic coatings or top coats.

Q. How many cars we can coat with a 30ml bottle?
A. About 20ml will go in mid-size SUV( Creta size) and large SUVs will consume 30ml Approx( Innova Size)

Q. Can I use TarX on the Gliss?
A. No, only for a small quick spot treatment.

Q. How long will the durability last?
A. We believe up to 12 months, if well maintained with CARPRO Reset.

Q. Can I use Gliss on top of protection film (PPF)?
A. Yes, it will bond well and become hydrophobic. We recommend testing in an inconspicuous area first since there are many different types of PPF.

Q. Will this work over other coatings or CQUARTZ coatings only?
A. We haven’t tested it on other coatings but it will work on some of them or in replacement of some of them.

Q. How glossy and slick is it compared to CQUARTZ coatings?
A.  Much more slick than CQUARTZ. Gloss will come mostly from polishing but it is slightly glossier than CQ by itself.

Q. So… if I understand correctly, THIS is a coating for coatings.  If my car were coated in CQUK or regular CQUARTZ, I would apply Gliss over the CQUARTZ UK to increase the slickness feel.  I was under the understanding that the point of coatings was we didn’t have to put anything on top of it. Please advise, I’m confused.
A1. That’s correct, you do NOT need to apply this on top of your CQUARTZ. You could continue on with Reset washes regularly, and occasionally decontaminating with Iron X and if you like Reload or Hydrofoam too (IF you want).

A2. Gliss can be applied a few hours after coating to provide a slicker surface which coatings lack and to assist in water spot resistance but again these are choices- not necessities.

A3. You could ALSO use Gliss by itself instead of a coating for someone afraid of using a heavy-duty coating like the UK, they could use GLISS as it is VERY visible when it’s ready to wipe off etc.